FISHER VALVE POSITIONER SERIES 3600 CALIBRATION

  • No Comments

Changing the nozzle position is intended only as a means of zero trim adjustment. Apply an input signal equal to the low value of the input signal range. Move the flapper assembly to approximately position 6 in the proper operating quadrant of the beam direct or reverse acting , and apply supply pressure to the valve positioner. This could be catastrophic and lead to undesirable consequences. The valve positioner is a critical component in the control valve loop as it helps to accurately position the valve during the control process. Note that Moving the flapper assembly toward zero on the beam scale decreases stem travel.

If not, first check for loose linkage or improper cam installation. If the desired stem travel occurs before the input signal reaches the high value of the input signal range, decrease the travel by moving the flapper assembly toward a lower number on the beam. Connect the input to the valve positioner and set the input signal value at mid-range. Apply an input signal equal to the high value of the input signal range 15psig, if using a 3 to 15psig positioner and observe the actuator stem travel. Move the flapper assembly to approximately position 6 in the proper operating quadrant of the beam direct or reverse acting , and apply supply pressure to the valve positioner. Imagine supplying a customer natural gas at 5barg through a control valve controlled by a controller taking signal from the supply to the customer. If pressure suddenly goes to 7barg and the controller gives a signal to the control valve to close more to bring the pressure to 5barg, if the control valve is wrongly positioned and fails to close more, we could be giving the customer more than 5barg!

Cslibration ValvesPneumatic Systems. If the stem travel is short of its expected range, increase the travel by moving the flapper assembly to a higher number on the beam.

  SHIKABANE HIME AKA EPISODE 8 ENGLISH SUB

How to Calibrate the Fisher 3582i Positioner

Newer Post Older Post Home. This could be catastrophic and lead to undesirable consequences. Apply an input signal equal to the high value of the input signal range 15psig, if using a 3 to 15psig positioner and observe the actuator stem travel. Each time the flapper assembly position is changed in step 4, repeat step 3 to provide proper zero. If pressure suddenly goes to 7barg and the controller gives a signal to the control valve to close more to bring the pressure to 5barg, if the control valve is wrongly positioned callbration fails to close more, we could be giving the customer more than 5barg!

Loosen the nozzle locknut and adjust the nozzle until the actuator moves to the proper end of its travel. Connect the input to the valve positioner and set the input signal value at mid-range. The valve positioner is a critical component in the control valve loop as it helps to accurately position the valve during the control process.

Before studying this procedure, read: The 0 degree index seried on the rotary shaft arm should align with the case index marks as shown in diagram below and the actuator should be at its mid-travel position.

Share to Twitter Share to Facebook.

If your positioner is a 0. Control Valves, Pneumatic Systems. Repeat steps 3 and 4 until the correct travel is achieved. A minor nozzle height adjustment might be necessary to make the desired input signal value correspond to the starting point of travel.

The set up below illustrates the basic components required to calibrate a control valve positioner:. However, failure to calibrate the positioner accurately could lead to wrong valve positioning which could in turn have significant impact on the process where the control valve is being used. Imagine supplying a customer natural gas at 5barg through a control valve controlled by a controller taking signal 3060 the supply to the customer.

  MASTERS OF HORROR CIGARETTE BURNS INCUBO MORTALE STREAMING

If the desired stem travel occurs before the input signal reaches the high value of the input signal range, decrease the travel by moving the flapper assembly toward a calivration number on the beam. Changing the nozzle position is intended only as a means of zero trim adjustment. Apply an input signal equal to the low value of the input signal range.

If not, first check for loose linkage or improper cam installation. Note that Moving the flapper assembly toward zero on the beam scale decreases stem travel.

Whenever nozzle position is changed, the zero reference point is changed. Positioner Beam and Arm Index Marks. How a Pneumatic Valve Positioner Works.

How to Calibrate the Fisher i Positioner – Control Valves – Emerson Process Video Library

ppositioner Shut off the supply pressure to the positionre positioner. In view of the importance of a positioner in accurately positioning the control valve plug, the need to accurately calibrate the valve positioner cannot be over emphasized. Connect or reconnect the necessary tubing from the valve positioner output to the actuator supply connection. Move the flapper assembly to approximately position 6 in the proper operating quadrant of the beam direct or reverse actingand apply supply pressure to the valve positioner.