• No Comments

Page of 8 Go. If possible, retain the carton, including the original packing materials. Dispose of Dell equipment per local regulations. Equipment not suitable for use in the presence of flammable mixtures. The default IP address of the controller is Originated in the USA.

For the most current information about Global Environmental Compliance and Dell products, visit dell. All other trademarks are the property of their respective owners. Enter text from picture: The installation consists of the following steps: Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots at approximately a degree angle to the ceiling tile rail see Figure 7. Make sure that these sources are taken into consideration when you attach an AP to its fixed location. Page 2 Yes to proceed with the Setup Wizard. Dell controller with appropriate power cord and accessories.

No modifications are allowed without Dell approval.


Dell, in compliance with governmental requirements, has designed the WAP Series access points so that only authorized network administrators can powerconhect the settings. Press and hold the reset button using a small, narrow object, such as a paperclip. The Startup Wizard is available the. The default certificate installed in the controller does not guarantee security in production networks. Inform your supplier if there are any incorrect, missing, or damaged parts.

The power LED will flash again within 15 seconds indicating that the reset is completed. Got it, continue to print. Dell strongly recommends that you replace the default certificate with a custom certificate issued for your site or domain by a trusted Certificate Authority. After WLAN planning is completed and the appropriate products and their placement have been determined, the Dell controller s must be installed and initial setup be performed before the Dell APs are deployed.


Comments to this Manuals Your Name: Specifically, you must verify the following conditions: Make sure the AP fits securely on the ceiling tile rail when hanging the device from the ceiling, because poor installation could cause it to fall onto people or equipment.

Wipe with a dry cloth, no additional maintenance required. Equipment not suitable for use in the presence of flammable mixtures.

Make sure that any cable slack is above the ceiling tile. It’s a community-based project which helps to repair anything. Indicates the status of the 2. The port has RJ female connectors with the pin-outs shown in Figure 5.

The default IP address of dlel controller is Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture 47 CFR 1. The AP will now continue to boot with the factory default settings.

They use MIMO Multiple-in, Multiple-out technology and other high-throughput mode techniques to deliver high-performance, Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks into place on the ceiling tile rail. RF Radiation Exposure Statement: After the controller has booted up, you should see a screen ztart to the following Access points are radio transmission devices and as such are subject to governmental regulation.

The installation consists of srubaos following steps: Before You Begin Caution: Connect it directly to a terminal or terminal server using an Ethernet cable. Improper termination of access points installed in the United States configured to non-US model controllers will be in violation of the FCC grant of equipment authorization.

Dell provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Dell hardware products.


You can launch the setup wizard using any PC or workstation that can run a supported Web browser. This equipment should be installed and operated with a minimum distance of 7. To print the manual completely, please, download it. Use these materials to repack and return the unit to the supplier if qiuck.

Dell PowerConnect W-651 Quick Start Manual

powerconnec This port is a RJ female connector with the pinouts described in Figure 4. BuildingCitygate Mahon Cork Ireland 10 Website Support If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: All other trademarks are the property of their huide owners. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots at approximately a degree angle to the ceiling tile rail see Figure 7.

Indicates the status of the 5 GHz Make sure that the controller is not connected to any device on your network. This product includes software developed by Lars Fenneberg, et al. These local AP parameters are initially configured on the controller which are then pushed out to the AP and stored on the AP itself.

Page 2 Yes to proceed with the Setup Wizard.